I would recommend Web Don for all finishing products.. they help you get the job done right.
↧
Topic "Product and maybe contractor?" a message from bjackson
↧
Topic "6 Ways to Help You Select Right Laminate Flooring" a message from Becky Li
Are you still puzzled by selecting right laminate floorings? Here under are six methods for your reference to make the right choice.
No. 1 Select Famous Laminate Flooring Manufacturers and Distributors
Laminate flooring is a product with high technique and it’s quite difficult to know its quality only judging from appearance without professional quality tests. So we suggest consumers to buy from famous suppliers because they are experienced with offering both high quality products and good service. You may get durable products with 20 to even more guarantee which lower your interior decoration cost relatively. And the professional workers will recommend you which are commercial laminate floorings and which are for residential use. If you are now sure whether the supplier you’re contacting is good, you may also check some laminate flooring reviews from the related forums. What’s more, large suppliers can offer laminate flooring accessories as well. In that case, you could get all the products you need only from one “shop”.
No. 2 Judge from Wear-resisting Revolutions
The wear resistance of laminate flooring mainly depends on the dosage of aluminum trioxide on the surface. And certain dosage of aluminum trioxide decides the wear-resisting revolutions of laminate flooring. For residential use, the wear-resisting revolutions should be more than 6000, for commercial use in public places, more than 9000. You may make your personal choice per the practical needs.
No. 3 Check Release Amount of aluminum trioxide
Aluminum trioxide definitely exists in laminate flooring, but if the value is more than 1.5mg/L, the flooring products will do harm to human body. So during purchasing you need to select products with national green certificate.
No. 4 Check Density of Core Board
The density of laminate flooring core board (HDF) should be 0.82-0.96 g/cm3, either lower or higher will be improper.
No. 5 Check Water-proof Performance
The thickness swelling rate indicates the water-proof performance of laminate flooring. The higher the rate is, the better the performance appears. And low water-proof laminate floorings will distort or change at size in humid environment.
No. 6 Check the Installation Effect
Put 6 to 12 pieces of planks into installation, and observe whether the joining point is smooth, if the tongues and grooves are matched properly, neither too loose or too tight. Besides, you need to check the height difference and opening distance of joined planks.
After those 6 methods above, are you clear about how to select right laminate floorings now?
No. 1 Select Famous Laminate Flooring Manufacturers and Distributors
Laminate flooring is a product with high technique and it’s quite difficult to know its quality only judging from appearance without professional quality tests. So we suggest consumers to buy from famous suppliers because they are experienced with offering both high quality products and good service. You may get durable products with 20 to even more guarantee which lower your interior decoration cost relatively. And the professional workers will recommend you which are commercial laminate floorings and which are for residential use. If you are now sure whether the supplier you’re contacting is good, you may also check some laminate flooring reviews from the related forums. What’s more, large suppliers can offer laminate flooring accessories as well. In that case, you could get all the products you need only from one “shop”.
No. 2 Judge from Wear-resisting Revolutions
The wear resistance of laminate flooring mainly depends on the dosage of aluminum trioxide on the surface. And certain dosage of aluminum trioxide decides the wear-resisting revolutions of laminate flooring. For residential use, the wear-resisting revolutions should be more than 6000, for commercial use in public places, more than 9000. You may make your personal choice per the practical needs.
No. 3 Check Release Amount of aluminum trioxide
Aluminum trioxide definitely exists in laminate flooring, but if the value is more than 1.5mg/L, the flooring products will do harm to human body. So during purchasing you need to select products with national green certificate.
No. 4 Check Density of Core Board
The density of laminate flooring core board (HDF) should be 0.82-0.96 g/cm3, either lower or higher will be improper.
No. 5 Check Water-proof Performance
The thickness swelling rate indicates the water-proof performance of laminate flooring. The higher the rate is, the better the performance appears. And low water-proof laminate floorings will distort or change at size in humid environment.
No. 6 Check the Installation Effect
Put 6 to 12 pieces of planks into installation, and observe whether the joining point is smooth, if the tongues and grooves are matched properly, neither too loose or too tight. Besides, you need to check the height difference and opening distance of joined planks.
After those 6 methods above, are you clear about how to select right laminate floorings now?
↧
↧
Topic "Hallmark floating floor started crackling [video]" a message from dbwatson
In any installation expansion is critical to the performance of the product. Can you check to see that the flooring is not touching any stationary objects such as walls or posts? Sounds like the floor may be under stress from lack of expansion. What part of the country are you located?
Not sure about the injection of glue between boards. I am not familiar with this procedure.
Not sure about the injection of glue between boards. I am not familiar with this procedure.
↧
Topic "Points Consumers Concern About Laminate Flooring" a message from Becky Li
With the continuous improvement of laminate flooring technique, more and more consumers would like to select laminate flooring as their decoration material. According to flooring manufacturers in China, the top three points that customers concern most can be concluded as follows.
Firstly, the surface types of floors. Consumers usually have an initial plan about how they will design the room and with what decoration effect it will be. Following their actual needs, they will come to select surfaces. There are about 12 surface types existing in the market, either rough or smooth. Among them, embossed laminate flooring is quite popular because the concave and convex textures make it more similar to real wood floor. Embossed laminate flooring is divided into three types according to the texture density and distance; they are small embossed, middle embossed and large embossed laminate flooring. Consumers could make practical procurement as per their needs.
Secondly, the wearing resistance layer of laminate flooring. European standards divide the wearing resistance layer into 5 different levels according to the wear-resisting revolutions, which are AC1, AC2, AC3, AC4 and AC5. The higher the level is, the better the wear resistance performance acts. Normally speaking, AC4 laminate flooring is proper for commercial use and it is hotly welcomed by shopping mall, office and other public places where there will be more traffic. While for residential use like living room, bed room, AC3 will be good enough.
Thirdly, the colors that laminate floorings appear. With advanced design and printing techniques, more and more imitating wood colors are created. You may find wood colors like pine, cherry, maple and walnut; you also could get cloth or stone colors. While generally speaking, wood colors are more popular, especially pine wood colors. Recently, more than 5 customers have enquired our knotty pine laminate flooring because they think the knotty design and color tone are quite similar to real pine wood.
Above are three aspects that consumers concern. Of course, they may have other considerations such as the waterproof performance, the size and thickness. No matter what they care about, manufacturers are pleased to meet their needs because the customer is god.
edited by Becky Li on 4/3/2014
edited by Becky Li on 4/3/2014
Firstly, the surface types of floors. Consumers usually have an initial plan about how they will design the room and with what decoration effect it will be. Following their actual needs, they will come to select surfaces. There are about 12 surface types existing in the market, either rough or smooth. Among them, embossed laminate flooring is quite popular because the concave and convex textures make it more similar to real wood floor. Embossed laminate flooring is divided into three types according to the texture density and distance; they are small embossed, middle embossed and large embossed laminate flooring. Consumers could make practical procurement as per their needs.
Secondly, the wearing resistance layer of laminate flooring. European standards divide the wearing resistance layer into 5 different levels according to the wear-resisting revolutions, which are AC1, AC2, AC3, AC4 and AC5. The higher the level is, the better the wear resistance performance acts. Normally speaking, AC4 laminate flooring is proper for commercial use and it is hotly welcomed by shopping mall, office and other public places where there will be more traffic. While for residential use like living room, bed room, AC3 will be good enough.
Thirdly, the colors that laminate floorings appear. With advanced design and printing techniques, more and more imitating wood colors are created. You may find wood colors like pine, cherry, maple and walnut; you also could get cloth or stone colors. While generally speaking, wood colors are more popular, especially pine wood colors. Recently, more than 5 customers have enquired our knotty pine laminate flooring because they think the knotty design and color tone are quite similar to real pine wood.
Above are three aspects that consumers concern. Of course, they may have other considerations such as the waterproof performance, the size and thickness. No matter what they care about, manufacturers are pleased to meet their needs because the customer is god.
edited by Becky Li on 4/3/2014
edited by Becky Li on 4/3/2014
↧
Topic "oil finish not drying" a message from TomD
I have a contractor who used Oxalic Acid (1 pint to a 1 gal) to bleach out some stains in a room. He then came back and buffed in a coat of oil. After 24 hours the floor that was treated had not dried completely . Unfortunately(?) he was able to get a coat of poly on the top and that has not dried completely either. I recommended he wait another day. Anyone have experience with Oxalic Acid?
Tom
Tom
↧
↧
Topic "Different Eng Adhesive Question" a message from LesFlo
Okay this has been a while.
Look guys I know most of that.
With the exception of the "conservation of linear momentum" bit
which started as "elasticity of momentum".
I don't even want to know how that changed![Cool]()
No we don't move pianos or pool tables either
Nor will we disconnect or re-connect any electronics.
It was a matter of curiosity.
Look guys I know most of that.
With the exception of the "conservation of linear momentum" bit
which started as "elasticity of momentum".
I don't even want to know how that changed
No we don't move pianos or pool tables either
Nor will we disconnect or re-connect any electronics.
It was a matter of curiosity.
↧
Topic "Rubio" a message from Kevin
Anything I should know about Rubio Chocolate on Ash. We have recently completed a project on oak. The current wood being installed is Ash and I would sincerely love a heads up on what I might experience with Ash. Thanks
↧
Topic "REGARDING TELLING THE CLIENT TOO MUCH" a message from Jim Decker
I hesitated posting this but what the hell!
Regarding telling the client too much!
When I explain about the manufacturers requirements for relative humidity, temperature and care and maintenance and show them some samples of face checking and separation of veneer from core.
I almost always get the negative response “Humm, maybe I shouldn’t get wood after all.”
My response always is this “You know I almost always get that response but consider this”.
When you purchase a new car the dealer/manufacturer insists on regular checkups and maintenance in order for your new car warranty to be in force. Why, they know what can happen when their guidelines are not followed and state clearly if they are not followed you have no warranty.
So do people not buy a new car? Of course not! Generally they are happy that problems will be taken care of if …………..they allow the dealer/mfg guidelines to be followed.
Regarding wood floors if you follow a few mfg guidelines regarding installation and care and maintenance there will be no problem. Humidify or dehumidify, if necessary, as every house and family is different. Most clients observe their hygrometer and then decide if it is really necessary.
Doctors advise low humidity can lead to stuffed up noses, dry mouth, itchy skin and a whole host of ailments regarding dryness. Also, humidified air allows one to lower their thermostat in the winter allowing a savings on heating bills.
We will give you the information to insure your investment will not be wasted. Our competition is not even aware of what I am telling you though they should be!
As a wood inspector all I ever see is failure and inevitably it is due to the fact no one told them.
I learned this technique from being a student of Warren Tyler a pretty smart customer. He teaches sales people how to overcome objections quite well.
http://www.floorcoveringinstitute.com/Warren_Tyler.html
Additionally, due to numerous certificates of completion of basic, intermediate and advanced sand and finish, installation, inspector school courses, from the NWFA of which we are a member, over the years we can insure that though we do charge a little more, the ADDED VALUE insures they will be assured of a project that will incur no problems at the time of installation or in the future.
We have been the recipient of Best Hardwood Floors in El Paso for the last 5 years by El Paso Magazine coupled with a roughly 75% referral rate I would say that speaks for itself. We do not advertise at all in the media. We have had a 2,000 sq. ft. storefront operation for the past 12 years.
The owner has a plaque over his desk that states “It ain’t BRAGGIN if you can do it”.
Regarding telling the client too much!
When I explain about the manufacturers requirements for relative humidity, temperature and care and maintenance and show them some samples of face checking and separation of veneer from core.
I almost always get the negative response “Humm, maybe I shouldn’t get wood after all.”
My response always is this “You know I almost always get that response but consider this”.
When you purchase a new car the dealer/manufacturer insists on regular checkups and maintenance in order for your new car warranty to be in force. Why, they know what can happen when their guidelines are not followed and state clearly if they are not followed you have no warranty.
So do people not buy a new car? Of course not! Generally they are happy that problems will be taken care of if …………..they allow the dealer/mfg guidelines to be followed.
Regarding wood floors if you follow a few mfg guidelines regarding installation and care and maintenance there will be no problem. Humidify or dehumidify, if necessary, as every house and family is different. Most clients observe their hygrometer and then decide if it is really necessary.
Doctors advise low humidity can lead to stuffed up noses, dry mouth, itchy skin and a whole host of ailments regarding dryness. Also, humidified air allows one to lower their thermostat in the winter allowing a savings on heating bills.
We will give you the information to insure your investment will not be wasted. Our competition is not even aware of what I am telling you though they should be!
As a wood inspector all I ever see is failure and inevitably it is due to the fact no one told them.
I learned this technique from being a student of Warren Tyler a pretty smart customer. He teaches sales people how to overcome objections quite well.
http://www.floorcoveringinstitute.com/Warren_Tyler.html
Additionally, due to numerous certificates of completion of basic, intermediate and advanced sand and finish, installation, inspector school courses, from the NWFA of which we are a member, over the years we can insure that though we do charge a little more, the ADDED VALUE insures they will be assured of a project that will incur no problems at the time of installation or in the future.
We have been the recipient of Best Hardwood Floors in El Paso for the last 5 years by El Paso Magazine coupled with a roughly 75% referral rate I would say that speaks for itself. We do not advertise at all in the media. We have had a 2,000 sq. ft. storefront operation for the past 12 years.
The owner has a plaque over his desk that states “It ain’t BRAGGIN if you can do it”.
↧
Topic "Favorite orbital sanders???" a message from Arkansasandman
I like to orbit all my edges after fine edging and befor I screen. Last 3 or 4 years I've been buying those 6 inch rigid orbital from Home Depot, I'm not happy at all with them. I can buy 3 in one day and they all seem to orbit with different aggressiveness and don't last very long. And I'm not someone who like to be returning tools all the time so I'm searching for a orbital I can purchase and have for years..... I'm currently considering the festool rotex150 and was curious what other floor pros that orbit are using and are happy with. Thanks in advance
↧
↧
Topic "Maple island question?" a message from Arkansasandman
My customer has a 5x10 maple butcher block island that she does not use for food prep she uses it like a normal countertop or table, she want a hard low shine finish so I was thinking of putting bona traffic satin on it but then found out she has been putting mineral oil on it so now I don't know what to tell her. My question is should she just keep putting mineral oil on it or is there a finish of some type that will adhere to this oil. Thanks
↧
Topic "Bamboo" a message from jvino
I know that it's an old conversation but I found and read the document.
http://www.klebstoffe.com/fileadmin/redaktion/ivk/Merkblaetter/TKB_1_englisch.pdf
http://www.klebstoffe.com/fileadmin/redaktion/ivk/Merkblaetter/TKB_1_englisch.pdf
↧
Topic "Expansion Joint Question" a message from dmhrdwd
really just because that is what is recomended does not say that is what you should do climate is in questinon !!!!
↧
Topic "Angry Contractor" a message from dmhrdwd
Well to be honest both of you need tooo chill out cuz both r wrong
↧
↧
Topic "wood floor in a basament" a message from dmhrdwd
call me Dave at dmhardwood designgns 303 954 9398
↧
Topic "Exstreame advanced school" a message from dmhrdwd
This school is to get the young and upcomoning to know how to win floor of the year1111
DO you want6 tooo!!!!! win floor of the YEAR? then think!!! riight????
DO you want6 tooo!!!!! win floor of the YEAR? then think!!! riight????
↧
Topic "110v belt sanders?" a message from sc_hardwood_guy
Any one out there use a 110v belt or drum sander? if so how do you like it?
↧
Topic "Lägler Flip" a message from sc_hardwood_guy
Any of you use a Lägler Flip edger? if so how do you like it?
↧
↧
Topic "so much dust! what do you guys do?" a message from john.fellows
Hi guys. I'm still new to installing floors, but did work for a some contactors down in Texas for about a year. Now I've moved up to Minnesota and see guys here do things alot different. What I can't understand is how your supposed to cut flooring in the cold and snow. Most all the jobs we had in Texas, we wuld find a spot on a porch or somethiung outside. Up here the guys just set up the saws in people houses and the dust flys everywhere. It doesn't seem right or is it what every one does?
↧
Topic "Engineered floor unglued from concrete" a message from JLW71
I have a 3/8" x 3" engineered oak floor that is separating from concrete foundation. What is the best way to secure without ripping it up? I have read about products such as "Fix A Floor" but unsure of application. Any advice is appreciated.
↧
Topic "Allowable width differences" a message from Jeff
Ok...I've gone off on flooring mill rants in the past, so I will try to keep my composer. I'm installing 1200sqft of random width (3 1/4",5") 2nd & btr maple in a new home here in Iowa City. Wood is from a "good" mill (although ive had issues in the past). The 5" boards vary in width by as must as 3/32" some are a full 1/16th under and some are 1/32" over, maybe a hair more. It doesn't seem to be that one bundle is all one size and others are different. I know wide plank can get a little funky especially on the ends, but this is constistant.
So is this ok or do I have a legitimate complaint?
So is this ok or do I have a legitimate complaint?
↧